Top 10 Jeep Commander Dash Vents

Up until now installing an Aftermarket Double Din Radio into the 2005-2007 Jeep Grand Cherokee meant having to buy the factory navigation bezel ( 175 ), an aftermarket radio install dash kit ( 12 ), wiring harness and a antenna adapter (6). However our new kit allows you to replace your Factory Radio with an aftermarket Double Din radio at a reasonable price with a cleaner look. We have taken the extra steps out for buying multiple parts and lowered the price plus you will get a better looking installed with our kit. This wire harness is compatible with standard wiring only. Will not work on models with Factory Infinity Systems, Boston Acoustic Systems or CAN Bus Radios (models REF, REC, RAQ or RAK; The radio’s name can be found on the face of the radio). Installation Directions- Tools needed for install – Philips screw driver, Dremel (rotary tool) and a Soldering Iron. You can buy a Soldering gun at Harbor freight for as low as 3.99 and a Dremel (rotary tool) knock off for 10.79 or just look on Amazon. Step 1: Gently pull on the factory bezel, it is only held on by a few plastic tabs up top and there are 2 clips on each side of the AC vents (totaling 4) and 1 clip at the bottom.. Step 2: You will see 4 Philips screws holding the factory radio in place, remove the screws and the radio will be lose and ready to come out.. Keep the screw for installation of new double din radio.. Step 3: Next unplug all the wire harness and antenna cable leading into the factory radio. You will now have the empty hole ready for new double din radio and your newly purchased dash kit (DO NOT DISCARD THE FACTORY BEZEL AS YOU WILL NEED THE AC VENTS TO PUT ON THE NEW BEZEL) Step 4: The removal of the AC vents from the factory bezel.

Finally a Double Din Radio installation solution is in reach without having to pay tons of money for a custom handmade kit (these cost upwards of $349)!!! Installation Directions: 1. In the lower pocket area remove the one screw located in the center 2. Pry out on the factory bezel and separate it from the dash 3. Disconnect AC harness and the cigarette lighter 4. Remove the 4 Philip screws that hold the radio in place 5. Pull radio forward and disconnect the wire harness and antenna 6. Unmount the AC system from the factory bezel by removing the 4 Philip screws 7. Reattach that to the new double din bezel 8. Remove the old factory cigarette lighter and install on new double din bezel 9. Slide out the pocket liner and install on the new double din bezel 10. Remove radio supports by removing the 4 Philips (see picture gallery) 11. Use a drimmel or other plastic cutting device to remove the necessary plastic from the inside of the dash (see picture gallery) 12. Take the new bezel brackets and loosely attach to the new double din bezel 13. Dry fit your aftermarket double din radio into the bezel and remove/add any necessary trim rings/cages 14. Then line up aftermarket radio with the brackets and loosely screw through the brackets into the radio 15. Slide the aftermarket radio forward and back until you achieve a clean finish 16. Making sure the aftermarket radio is its square tighten all screws 17. Wire in the aftermarket radio to the aftermarket harness 18. Install antenna adapter 19. Reconnect the AC controls and lighter button with harnesses in the dash 20. Plug aftermarket wire harness into the factory radio harness. 21. Snap bezel into place and secure final screw in lower pocket area.

Flexible and Tough – Flex Tough Tortoise series mats are designed to provide maximum protection. The uniquely constructed linear and diagonal ridges are placed strategically to maximize the dirt trapping capabilities of the mat. Made from only the highest quality polymers, Motor Trend Mats are Odorless and Non-Toxic. Trim able for Extra Customization. Deep Inverted Shell Design. No slip nibbed backing

18-19 Jeep Wrangler JL Rear Bumper w/ 2X18W Nilight Upgraded LED Lights & 2″ Hitch Receiver D Rings Introduction : Upgrade your 18-19 Wrangler for adventurous off-road performance by investing in the Rear Bumper. The heavy duty rear bumper is engineered for functional protection and extreme style. Specification: Color: Textured black. Material: Heavy Duty 3/16″ Steel Construction Fitment: 2018+ Jeep Wrangler JL all model. Features: 1. Direct bolt-on replacement of original bumper. No cutting or drilling required. 2. Made from durable steel sheet. 3. Premium Two Stage Textured Black Powder Coat Finish for corrosion protection and durability. 4. High strength D-ring mounts are robotically welded both inside and outside. 5. D-rings with black isolators included – 9, 500 lbs each. 6. 2″ Standard Hitch Receiver 7. Accommodates Up to a 37″ Tire 9. Ultra-Rugged, one-piece fully welded design for extra strength 10. Professional packaging, true 360° Protection Easy Bolt-on Installation Nilight Bumpers are engineered to be a direct bolt-on upgrade using just basic hand tools, so there is no drilling or cutting required for a clean straight forward installation. Package included: 1x JL Rear Bumper with 2″ Standard Hitch Receiver 2x 18W Nilight Upgraded New Design Flush Mount LED Pods 2x D-ring shackles + Isolators + Washers All Mounting Hardwares. Note: Please verify that off road Jeep Wrangler JL rear bumper fit your vehicle before you purchase.

Motor Trend Mats are manufactured with the highest quality and safest material. means you and your family don’t need to worry about toxins and odors that other rubber mats emit. These mats give your floor All-Weather protection and keeps your car free from any messes from spills, loose dirt, or water. The rubberized nibs on the backing prevents the mats from sliding around when driving or getting in and out of the car. These mats are easily trimmable to accommodate pedal placement and any necessary customization. For Full Protection, the purchase comes with 2 Front Mats and 2 Liners for all three Row Vehicles. Please check measurements before installation. BDK: Superior Quality – Premium Material – Fresh Design

This is a Power Acoustic PD-710B 7″ TFT touch screen single DIN car player. The Power Acoustik PD-710B features detachable motorized faceplate with angle adjustment, it plays CD’s, DVD’s, MP3’s, has built in Bluetooth, multi region FM frequency stepping, rear view camera input with trigger, has USB, SD and Aux ports and comes with a wireless remote control. AUX A/V Input for Personal Media Devices, 52w x 4 MOSFET Speaker Outputs

Specification: material: black nylon, suitable for car Use better replacement for original old worn broken one. Push  type, easy to fasten.

AVS In-Channel Ventvisor Side Window Deflectors are designed to complete the look of your vehicle adding subtle style while maintaining the functionality you desire from a side window deflector. The Ventvisor installs in the window channel for a streamlined appearance, but still allows fresh air to naturally circulate through open windows while keeping the rain and wind out. There is no special hardware needed and no drilling required, the In-Channel’s patented design easily secures into the window channel or along the rubber seal with pre-applied 3M automotive tape. Absolutely no tape touches your vehicle’s finish. Additionally, the product keeps the sun out of your eyes and allows you to keep your window cracked while parked, keeping the interior cooler.