Top 10 Dash Besil

Warped, cracked and missing pillar trims can take away from your vehicle’s appearance. This replacement door pillar trim matches the fit and finish of the factory trim and includes all new mounting hardware for a secure installation. Vehicle model years this part fits: Dodge Ram 1500: 1999, 2000, 2001 Dodge Ram 2500: 1999, 2000, 2001, 2002 Dodge Ram 3500: 1999, 2000, 2001, 2002

Easily Fix your dried, cracked instrument bezel without spending a lot of money on parts and labor. Also looks better than a fabric dash board cover. This instrument bezel completely replaces your factory dash and appear as new. Replace for 98-01 Dodge Ram 1500 98-02 Dodge Ram 2500 3500

Double DIN Dash Kit for 1999 – 2002 GM Full-size Trucks and SUV’s (models with message center in the factory instrument cluster). Painted scratch-resistant matte black. Factory matched texture style. High-grade ABS plastic construction.

Easily Fix your dried, cracked instrument bezel without spending a lot of money on parts and labor. Also looks better than a fabric dash board cover. This instrument bezel completely replaces your factory dash and appear as new.

Package Included:

Since 1979 DashMat has been the most recognized, best-selling dash protector available. Custom-patterned for a perfect fit, DashMats help protect the dash surface from UV sun and to cover blemishes and imperfections in older dashboards. DashMats keep the interior cooler in the summer and warmer in the winter while reducing hazardous windshield glare. The original DashMat is made of high-quality polyester fabric made from 100% post-consumer recycled plastic bottles. The soft Foss fiber carpet won’t fray or unravel and is available in various colors to match almost any interior.

Double DIN Installation Dash Kit for Select 1990-Up GM Vehicles

Finally a Double Din Radio installation solution is in reach without having to pay tons of money for a custom handmade kit (these cost upwards of $349)!!! Installation Directions: 1. In the lower pocket area remove the one screw located in the center 2. Pry out on the factory bezel and separate it from the dash 3. Disconnect AC harness and the cigarette lighter 4. Remove the 4 Philip screws that hold the radio in place 5. Pull radio forward and disconnect the wire harness and antenna 6. Unmount the AC system from the factory bezel by removing the 4 Philip screws 7. Reattach that to the new double din bezel 8. Remove the old factory cigarette lighter and install on new double din bezel 9. Slide out the pocket liner and install on the new double din bezel 10. Remove radio supports by removing the 4 Philips (see picture gallery) 11. Use a drimmel or other plastic cutting device to remove the necessary plastic from the inside of the dash (see picture gallery) 12. Take the new bezel brackets and loosely attach to the new double din bezel 13. Dry fit your aftermarket double din radio into the bezel and remove/add any necessary trim rings/cages 14. Then line up aftermarket radio with the brackets and loosely screw through the brackets into the radio 15. Slide the aftermarket radio forward and back until you achieve a clean finish 16. Making sure the aftermarket radio is its square tighten all screws 17. Wire in the aftermarket radio to the aftermarket harness 18. Install antenna adapter 19. Reconnect the AC controls and lighter button with harnesses in the dash 20. Plug aftermarket wire harness into the factory radio harness. 21. Snap bezel into place and secure final screw in lower pocket area.

Up until now installing an Aftermarket Double Din Radio into the 2005-2007 Jeep Grand Cherokee meant having to buy the factory navigation bezel ( 175 ), an aftermarket radio install dash kit ( 12 ), wiring harness and a antenna adapter (6). However our new kit allows you to replace your Factory Radio with an aftermarket Double Din radio at a reasonable price with a cleaner look. We have taken the extra steps out for buying multiple parts and lowered the price plus you will get a better looking installed with our kit. This wire harness is compatible with standard wiring only. Will not work on models with Factory Infinity Systems, Boston Acoustic Systems or CAN Bus Radios (models REF, REC, RAQ or RAK; The radio’s name can be found on the face of the radio). Installation Directions- Tools needed for install – Philips screw driver, Dremel (rotary tool) and a Soldering Iron. You can buy a Soldering gun at Harbor freight for as low as 3.99 and a Dremel (rotary tool) knock off for 10.79 or just look on Amazon. Step 1: Gently pull on the factory bezel, it is only held on by a few plastic tabs up top and there are 2 clips on each side of the AC vents (totaling 4) and 1 clip at the bottom.. Step 2: You will see 4 Philips screws holding the factory radio in place, remove the screws and the radio will be lose and ready to come out.. Keep the screw for installation of new double din radio.. Step 3: Next unplug all the wire harness and antenna cable leading into the factory radio. You will now have the empty hole ready for new double din radio and your newly purchased dash kit (DO NOT DISCARD THE FACTORY BEZEL AS YOU WILL NEED THE AC VENTS TO PUT ON THE NEW BEZEL) Step 4: The removal of the AC vents from the factory bezel.

Dorman 57900 Defrost Vent Cover

Up until now installing an Aftermarket Double Din Radio into the 2005-2007 Jeep Grand Cherokee meant having to buy the factory navigation bezel ( $175 ), an aftermarket radio install dash kit ( $12 ), wiring harness and a antenna adapter ($6). However our new kit allows you to replace your Factory Radio with an aftermarket Double Din radio at a reasonable price with a cleaner look. We have taken the extra steps out for buying multiple parts and lowered the price plus you will get a better looking installed with our kit. This wire harness is compatible with standard wiring only. Will not work on models with Factory Infinity Systems, Boston Acoustic Systems or CAN Bus Radios (models REF, REC, RAQ or RAK; The radio’s name can be found on the face of the radio). Installation Directions- Tools needed for install – Philips screw driver, Dremel (rotary tool) and a Soldering Iron. You can buy a Soldering gun at Harbor freight for as low as $3.99 and a Dremel (rotary tool) knock off for $10.79 or just look on Amazon. Step 1: Gently pull on the factory bezel, it is only held on by a few plastic tabs up top and there are 2 clips on each side of the AC vents (totaling 4) and 1 clip at the bottom.. Step 2: You will see 4 Philips screws holding the factory radio in place, remove the screws and the radio will be lose and ready to come out.. Keep the screw for installation of new double din radio.. Step 3: Next unplug all the wire harness and antenna cable leading into the factory radio. You will now have the empty hole ready for new double din radio and your newly purchased dash kit (DO NOT DISCARD THE FACTORY BEZEL AS YOU WILL NEED THE AC VENTS TO PUT ON THE NEW BEZEL) Step 4: The removal of the AC vents from the factory bezel.